360足球直播免费

EN CN

Home / Products / Crushing & sizing

Reversible Impact Hammer Mill
360足球直播免费


The PCFK series of Reversible Impact Hammer Mill, as an integrator of hammer mill and impact mill, is used for primary & secondary crushing of low- and medium-hardness materials.


Mainly used to crush

Coal for circulating fluidized bed boiler

Coking coal for coke even

Coal, coke, limestone, dolomite, lime and etc. for sinter plant

All kinds of low and medium hardness ore, such as iron ore, phosphate rock and etc.


Main features and advantages

Advanced design and various functions

Higher efficiency and reliable operation

Excellent uniformity of product size and low fine grain ratio


Working Principle


The uniform distribution of the feeding material at the entire width of the rotor via a vibrating feeder or a specially-designed inlet chute is requested for achieving an optimum final grain size as well as a uniform wear of the crushing parts.

After entering the crushing cavity, the feed material is grasped by the rotating beater heads and then thrown against the grinding face at high speed to be crushed and again rebound to beater heads. The material is gradually crushed in a course of dash and inter-collision repeatedly and discharged out of the end of grinding face.

Product size is determined by rotation speed of the rotor, weight of hammers and gap between the rotor and the grinding wall.


360足球直播免费

Product Features

    PCFK series of Reversible Impact Hammer Mill consists of rotor, crushing plate and adjusting units, housing, base frame, and drive unit.


    1. The left and right frames are symmetry to ensure the motor is reversible. Grinding faces are installed at both sides of the frame to make full use of both sides of   hammer head. The left and right housings can be opened up upto 45°max through hydraulic device to facilitate maintenance.


    2. Main shaft and hub discs are forged with quality steel and assembled in octagon structure to ensure that the working portion of main shaft is in uniform stresses and balance of the rotor, which also facilitates maintenance.


    3.The flexible connection of beater arms with heads can ensure that hammer mill is sturdy enough against the intrusion of foreign hard matter.


    4.Hammer heads are arranged in spiral for stable load and good crushing effect. The arms and heads are weighed by pairs to ensure exact balancing of the rotor. The arms are forged with quality steel and the heads are made of high wear-resistant alloy cast.


    5. Specially designed crushing plate are fitted on the grinding wall to guarantee the angle of incidence of the material against the grinding wall at nearly 90° for optimum crushing result. Gap between rotor and grinding wall can be adjusted to compensate wearing of grinding faces and change size of finished product.


    360足球直播免费


  • Standard type / Heavy type

    Normally, standard type of rotor and grinding faces are adopted for brittle material, and heavy type for hard material (limestone, iron ore and etc).

  • Drive mode

    Direct-coupling: Rotor shaft is driven by motor through fluid coupling with motor and mill arranged a straight line.

    360足球直播免费

    Parallel: Rotor shaft is driven by motor through big and small pulley besides coupling with motor and mill laid in parallel.

    360足球直播免费
  • Reversible / Non-reversible

    Reversible impact hammer mill is equipped with grinding faces at both sides, allowing reversible operation and thus utilization of heads and grinding faces at both sides. As the rotor of the non-reversible hammer mill operates in single-direction, the heads have to be reversed for use after being worn out on one side.

  • Shock absorption device

    E-motor and mill are fitted on a whole plate form, fitted with shock absorption units for lowering down motional load and noise effectively.

  • Bearing temperature & vibration detection device

    Bearing temperature and vibration amplitude can be detected and displayed at local instrument box with signals transmitted to central control room.

  • Bearing lubrication device

    Automatic oil or grease lubrication unit is adopted for bearings to get continuous and full lubrication and maintenance.

  • Fluidized bed drying system

    Fluidized bed drying system, integrating classifying, drying and crushing as a whole, can modify moisture while crushing selectively to meet process requirement.

Technical Specification

Model no.

Output (t/h)

Feed size(mm)

Output size(mm)

Motor power(kw)

Rotor diameter(mm)

Rotor length(mm)

PCFK1006

10-15

50/20

8/3

55

1000

600

PCFK1008

20-30

50/20

8/3

75

1000

800

PCFK1010

30-40

50/20

8/3

90

1000

1080

PCFK1012

50-60

50/20

8/3

132

1000

1240

PCFK1210

60-70

70/30

8/3

160

1200

1080

PCFK1212

80-90

70/30

8/3

185

1200

1240

PCFK1214

110-120

70/30

8/3

250

1200

1400

PCFK1414

130-150

70/30

8/3

280

1400

1400

PCFK1416

160-190

70/30

8/3

315

1400

1640

PCFK1612

140-160

80/30

8/3

355

1600

1240

PCFK1616

200-220

80/30

8/3

450

1600

1640

PCFK1618

250-280

80/30

8/3

630

1600

1800

PCFK1820

350-400

80/30

8/3

710

1800

2000

PCFK1825

500-550

80/30

8/3

800

1800

2500


Stay updated on your industry GET NEWSLETTER
Contact

Future Square, No.55 Industrial South Road, High-tech Zone, Jinan, China

+86-0531-83323931
huangfan@eadaece.cn

© 2020 ANDE Metallurgical Machinery Equipment Co., Ltd All rights reserved

Follow us
360足球直播免费

Attention to the official account of Ande metallurgy WeChat

ӣ易胜博ysb体育  IMapp  博猫官网登录地址  欧洲杯外围竞猜  多宝体育